NORMALLY: $1,070
Sponsored by Southern California Edison
For qualifiying contractors*:
ONLY $150
Get the technical knowledge you need to improve customers’ system performance, prevent CO hazards, and increase profitability.
Combustion Performance & Carbon Monoxide Safety
- Three-day Advanced HVAC Training
- You can earn certification in CO/Combustion Analyst certification plus NATE, BPI and State CEU’s (where applicable)
(800) 633-7058
lIVE, in-person instruction
Individual attention
hands-on testing & problem-solving
normally $1,070
three-day training
certification course
Combustion Performance & Carbon Monoxide Safety
Learn to improve system performance, prevent CO hazards, and increase profits
In this three-day certification class, HVAC professionals will learn how to:
- Identify common sources of carbon monoxide (CO) and measure the ambient CO levels
- Uncover combustion air and venting defects
- Verify equipment safety
- And much more…
Who should attend?
Field technicians and installers, owners and managers, service and installation managers, sales professionals, energy raters and comfort advisors
Discover more about NCI’s Combustion Performance and Carbon Monoxide Safety Training Course:
Download a PDF About This Course:
Click here to download a free PDF all about NCI’s Combustion Performance and Carbon Monoxide Safety course to your device.
Read an Article Related to This Course:
How many occupations directly impact consumer health and safety? Those who do are doctors and nurses, the police, fire safety forces, and the military. Usually, these groups respond to a known danger, health, or safety issue. But when HVAC contractors enter a building, we enter a world of unknowns. If we are not dedicating our efforts to the safety of the occupants, we are not doing our job … Continue reading
Combustion Performance & CO Safety Program Overview
Day One Agenda
Carbon Monoxide Safety Testing & Diagnostics
- Introduction to combustion performance
- Proper combustion testing locations
- Using safety and combustion test instruments
- CO sources, levels, and protocols
- NCI Combustion Performance Standards
-
Effects of combustion issues on energy efficiency
- Field-measured efficiency
- How to diagnose fuel and mechanical problems
Day Two Agenda
Combustion Performance & Diagnostics
- Troubleshooting combustion air problems
- Draft testing
- Diagnosing venting problems
- Seven common diagnostic issues
- How to use the combustion troubleshooting chart
- Combustion diagnostic procedures and reports
- Combustion repairs, adjustments, and upgrades
- Makeup air sizing and systems
Day Three Agenda
CO/Combustion Review & Certification
- Natural draft water heat repairs & adjustments
- Induced draft furnace repairs & adjustments
- Condensing furnace repairs & adjustments
- Natural draft boiler repairs & adjustments
- Hands-on exercises
The day concludes with NCI’s exclusive Carbon Monoxide & Combustion Analyst certification exam (optional)
normally:
$1,070
sce contractor pricing:
$150*
Student Testimonials
I loved the class on carbon monoxide and combustion analysis . I truly enjoyed it and it was honor to have been in your class.
The NCI classes I took were very informative to me. CO is no joke!
In the CO training, Jim Davis stated we would save somebody’s life and three days afterwards, I was certain I did.
Course Qualifies for NATE, BPI, & Most State CEUs.
Frequently Asked Questions
What's a typical training day like?
Generally in-person training days start at 8 AM and ends at either 4:30 or 5. Lunch and workbook are included. There are breaks throughout the day.
Online, live events: This training is held in four hour chunks online. See specific events for times. You will be able to log in earlier to try to reduce problems. These events are all lead live by one of NCI’s experienced instructors. There are breaks every hour.
Can I get certified in this training?
Yes. There is an optional certification exam on day three. By taking and successfully passing the exam, you’ll earn Carbon Monoxide & Combustion Analyst certification, which is valid for two years. This is the only certification of it’s kind.
Does this class count towards renewing my NCI CO certification?
Yes. There is a one-day option specifically for recertification. Please contact us to see if you qualify.
Does this class count for CEUs?
Please see our page about CEU‘s for more information or ask us for more information.
What do I need to bring to the training?
Please bring pencils and a calculator, and be ready to learn. You will receive detailed instructions before the event.
How do I attend the online training?
You’ll need a laptop, desktop computer or large tablet with internet. You won’t be able to participate well on a phone. You will receive detailed instructions before the event.
How do I qualify as an SCE Contractor?
You must do work/offer services in Southern California Edison’s service territory. If you have any questions, contact us at 800 633-7058.